Low Power Processor Architectures and Contemporary Techniques for Power Optimization – A Review

The technological evolution has increased the number of transistors for a given die area significantly and increased the switching speed from few MHz to GHz range. Such inversely proportional decline in size and boost in performance consequently demands shrinking of supply voltage and effective power dissipation in chips with millions of transistors. This has triggered substantial amount of research in power reduction techniques into almost every aspect of the chip and particularly the processor cores contained in the chip. This paper presents an overview of techniques for achieving the power efficiency mainly at the processor core level but also visits related domains such as buses and memories. There are various processor parameters and features such as supply voltage, clock frequency, cache and pipelining which can be optimized to reduce the power consumption of the processor. This paper discusses various ways in which these parameters can be optimized. Also, emerging power efficient processor architectures are overviewed and research activities are discussed which should help reader identify how these factors in a processor contribute to power consumption. Some of these concepts have been already established whereas others are still active research areas. © 2009 ACADEMY PUBLISHER

Modeling, design, and characterization of through vias in silicon and glass interposers

Advancements in very large scale integration (VLSI) technology have led to unprecedented transistor and interconnect scaling. Further miniaturization by traditional IC scaling in future planar CMOS technology faces significant challenges. Stacking of ICs (3D IC) using three dimensional (3D) integration technology helps in significantly reducing wiring lengths, interconnect latency and power dissipation while reducing the size of the chip and enhancing performance. Interposer technology with ultra-fine pitch interconnections needs to be developed to support the huge I/O connection requirement for packaging 3D ICs. Through vias in stacked silicon ICs and interposers are the key components of a 3D system. The objective of this dissertation is to model through vias in 3D silicon and glass interposers and, to address power and high-speed signal integrity issues in 3D interposers considering silicon biasing effects. An equivalent circuit model of the through via in silicon interposer (Si TPV) has been proposed considering the bias voltage dependent Metal-Oxide-Semiconductor (MOS) capacitance effect. Important design guidelines and optimizations are proposed for Si TPVs used in the signal delivery network, power delivery network (PDN), and as variable capacitors. Through vias in glass interposers (Glass TPVs) are modeled, designed and simulated by using electromagnetic field solvers. Signal and power integrity analyses are performed for silicon and glass interposers. PDN design is proposed by utilizing the MOS capacitance of the Si TPVs for decoupling.PhDCommittee Chair: Tummala, Rao; Committee Co-Chair: Swaminathan, Madhavan; Committee Member: Lim, Sung Kyu; Committee Member: Mukhopadhyay, Saibal; Committee Member: Sitaraman, Suresh; Committee Member: Sundaram, Venk

Manifold Learning Side-Channel Attacks against Masked Cryptographic Implementations

Masking, as a common countermeasure, has been widely utilized to protect cryptographic implementations against power side-channel attacks. It significantly enhances the difficulty of attacks, as the sensitive intermediate values are randomly partitioned into multiple parts and executed on different times. The adversary must amalgamate information across diverse time samples before launching an attack, which is generally accomplished by feature extraction (e.g., Points-Of-Interest (POIs) combination and dimensionality reduction). However, traditional POIs combination methods, machine learning and deep learning techniques are often too time consuming, and necessitate a significant amount of computational resources. In this paper, we undertake the first study on manifold learning and their applications against masked cryptographic implementations. The leaked information, which manifests as the manifold of high-dimensional power traces, is mapped into a low-dimensional space and achieves feature extraction through manifold learning techniques like ISOMAP, Locally Linear Embedding (LLE), and Laplacian Eigenmaps (LE). Moreover, to reduce the complexity, we further construct explicit polynomial mappings for manifold learning to facilitate the dimensionality reduction. Compared to the classical machine learning and deep learning techniques, our schemes built from manifold learning techniques are faster, unsupervised, and only require very simple parameter tuning. Their effectiveness has been fully validated by our detailed experiments

Within-Die Delay Variation Measurement And Analysis For Emerging Technologies Using An Embedded Test Structure

Both random and systematic within-die process variations (PV) are growing more severe with shrinking geometries and increasing die size. Escalation in the variations in delay and power with reductions in feature size places higher demands on the accuracy of variation models. Their availability can be used to improve yield, and the corresponding profitability and product quality of the fabricated integrated circuits (ICs). Sources of within-die variations include optical source limitations, and layout-based systematic effects (pitch, line-width variability, and microscopic etch loading). Unfortunately, accurate models of within-die PVs are becoming more difficult to derive because of their increasingly sensitivity to design-context. Embedded test structures (ETS) continue to play an important role in the development of models of PVs and as a mechanism to improve correlations between hardware and models. Variations in path delays are increasing with scaling, and are increasingly affected by neighborhood\u27 interactions. In order to fully characterize within-die variations, delays must be measured in the context of actual core-logic macros. Doing so requires the use of an embedded test structure, as opposed to traditional scribe line test structures such as ring oscillators (RO). Accurate measurements of within-die variations can be used, e.g., to better tune models to actual hardware (model-to-hardware correlations). In this research project, I propose an embedded test structure called REBEL (Regional dELay BEhavior) that is designed to measure path delays in a minimally invasive fashion; and its architecture measures the path delays more accurately. Design for manufacture-ability (DFM) analysis is done on the on 90 nm ASIC chips and 28nm Zynq 7000 series FPGA boards. I present ASIC results on within-die path delay variations in a floating-point unit (FPU) fabricated in IBM\u27s 90 nm technology, with 5 pipeline stages, used as a test vehicle in chip experiments carried out at nine different temperature/voltage (TV) corners. Also experimental data has been analyzed for path delay variations in short vs long paths. FPGA results on within-die variation and die-to-die variations on Advanced Encryption System (AES) using single pipelined stage are also presented. Other analysis that have been performed on the calibrated path delays are Flip Flop propagation delays for both rising and falling edge (tpHL and tpLH), uncertainty analysis, path distribution analysis, short versus long path variations and mid-length path within-die variation. I also analyze the impact on delay when the chips are subjected to industrial-level temperature and voltage variations. From the experimental results, it has been established that the proposed REBEL provides capabilities similar to an off-chip logic analyzer, i.e., it is able to capture the temporal behavior of the signal over time, including any static and dynamic hazards that may occur on the tested path. The ASIC results further show that path delays are correlated to the launch-capture (LC) interval used to time them. Therefore, calibration as proposed in this work must be carried out in order to obtain an accurate analysis of within-die variations. Results on ASIC chips show that short paths can vary up to 35% on average, while long paths vary up to 20% at nominal temperature and voltage. A similar trend occurs for within-die variations of mid-length paths where magnitudes reduced to 20% and 5%, respectively. The magnitude of delay variations in both these analyses increase as temperature and voltage are changed to increase performance. The high level of within-die delay variations are undesirable from a design perspective, but they represent a rich source of entropy for applications that make use of \u27secrets\u27 such as authentication, hardware metering and encryption. Physical unclonable functions (PUFs) are a class of primitives that leverage within-die-variations as a means of generating random bit strings for these types of applications, including hardware security and trust. Zynq FPGAs Die-to-Die and within-die variation study shows that on average there is 5% of within-Die variation and the range of die-to-Die variation can go upto 3ns. The die-to-Die variations can be explored in much further detail to study the variations spatial dependance. Additionally, I also carried out research in the area data mining to cater for big data by focusing the work on decision tree classification (DTC) to speed-up the classification step in hardware implementation. For this purpose, I devised a pipelined architecture for the implementation of axis parallel binary decision tree classification for meeting up with the requirements of execution time and minimal resource usage in terms of area. The motivation for this work is that analyzing larger data-sets have created abundant opportunities for algorithmic and architectural developments, and data-mining innovations, thus creating a great demand for faster execution of these algorithms, leading towards improving execution time and resource utilization. Decision trees (DT) have since been implemented in software programs. Though, the software implementation of DTC is highly accurate, the execution times and the resource utilization still require improvement to meet the computational demands in the ever growing industry. On the other hand, hardware implementation of DT has not been thoroughly investigated or reported in detail. Therefore, I propose a hardware acceleration of pipelined architecture that incorporates the parallel approach in acquiring the data by having parallel engines working on different partitions of data independently. Also, each engine is processing the data in a pipelined fashion to utilize the resources more efficiently and reduce the time for processing all the data records/tuples. Experimental results show that our proposed hardware acceleration of classification algorithms has increased throughput, by reducing the number of clock cycles required to process the data and generate the results, and it requires minimal resources hence it is area efficient. This architecture also enables algorithms to scale with increasingly large and complex data sets. We developed the DTC algorithm in detail and explored techniques for adapting it to a hardware implementation successfully. This system is 3.5 times faster than the existing hardware implementation of classification.\u2

A Survey of Fault-Tolerance Techniques for Embedded Systems from the Perspective of Power, Energy, and Thermal Issues

The relentless technology scaling has provided a significant increase in processor performance, but on the other hand, it has led to adverse impacts on system reliability. In particular, technology scaling increases the processor susceptibility to radiation-induced transient faults. Moreover, technology scaling with the discontinuation of Dennard scaling increases the power densities, thereby temperatures, on the chip. High temperature, in turn, accelerates transistor aging mechanisms, which may ultimately lead to permanent faults on the chip. To assure a reliable system operation, despite these potential reliability concerns, fault-tolerance techniques have emerged. Specifically, fault-tolerance techniques employ some kind of redundancies to satisfy specific reliability requirements. However, the integration of fault-tolerance techniques into real-time embedded systems complicates preserving timing constraints. As a remedy, many task mapping/scheduling policies have been proposed to consider the integration of fault-tolerance techniques and enforce both timing and reliability guarantees for real-time embedded systems. More advanced techniques aim additionally at minimizing power and energy while at the same time satisfying timing and reliability constraints. Recently, some scheduling techniques have started to tackle a new challenge, which is the temperature increase induced by employing fault-tolerance techniques. These emerging techniques aim at satisfying temperature constraints besides timing and reliability constraints. This paper provides an in-depth survey of the emerging research efforts that exploit fault-tolerance techniques while considering timing, power/energy, and temperature from the real-time embedded systems’ design perspective. In particular, the task mapping/scheduling policies for fault-tolerance real-time embedded systems are reviewed and classified according to their considered goals and constraints. Moreover, the employed fault-tolerance techniques, application models, and hardware models are considered as additional dimensions of the presented classification. Lastly, this survey gives deep insights into the main achievements and shortcomings of the existing approaches and highlights the most promising ones