Design Equations for Class-E Power Amplifiers

In literature, it is widely accepted that the design of Class-E Power Amplifier (PA) with finite dc feed inductance requires a long iterative solution procedure. To avoid such iterative solution methods, analytical design equations should be known. The problem associated with the finite dc feed inductance Class-E PA is usually ascribed to the fact that the circuit element values are transcendental functions of the input parameters which is assumed to prevent the derivation of exact or fully analytical design equations. Using a proper analytical method, exact design solutions for Class-E PA with any inductor value can however be derived. A mathematically exact analysis of the idealized Class-E PA with finite dc feed inductance has been done and analytical expressions showing the relation between the circuit elements and the input parameters are found. These analytical expressions have been simplified to obtain explicit, relatively simple design equations. In this paper, we present these relatively simple design equations. Using these design equations, Class-E PA with finite dc feed inductance can be designed without iterative design procedures. The current paper discusses these simplified versions of the exact solution of general Class-E PA with finite dc feed inductance Key Words- Power Amplifier, Class-E

The Switched Mode Power Amplifiers

Non

Switching mode power amplifier for bluetooth applications

Modern fully integrated transceivers architectures, require circuits with low area, low cost, low power, and high efficiency. A key block in modern transceivers is the power amplifier, which is deeply studied in this thesis. First, we study the implementation of a classical Class-A amplifier, describing the basic operation of an RF power amplifier, and analysing the influence of the real models of the reactive components in its operation. Secondly, the Class-E amplifier is deeply studied. The different types of implementations are reviewed and theoretical equations are derived and compared with simulations. There were selected four modes of operation for the Class-E amplifier, in order to perform the implementation of the output stage, and the subsequent comparison of results. This led to the selection of the mode with the best trade-off between efficiency and harmonics distortion, lower power consumption and higher output power. The optimal choice was a parallel circuit containing an inductor with a finite value. To complete the implementation of the PA in switching mode, a driver was implemented. The final block (output stage together with the driver) got 20 % total efficiency (PAE) transmitting 8 dBm output power to a 50 W load with a total harmonic distortion (THD) of 3 % and a total consumption of 28 mW. All implementations are designed using standard 130 nm CMOS technology. The operating frequency is 2.4 GHz and it was considered an 1.2 V DC power supply. The proposed circuit is intended to be used in a Bluetooth transmitter, however, it has a wider range of applications

Load-mismatch sensitivity of class-E power amplifiers

Class-E RF power amplifiers (PAs) are very power efficient under nominal operating conditions. Due to incorporating two tuned tanks, the dependence on the load impedance is, however, relatively large, resulting in, e.g., load-dependent output power, power efficiency, peak voltages, and peak (and average) currents which can lead to reliability issues. This paper presents load-pull analyses for class-E RF PAs from a mathematical perspective, with analyses and discussions of the effects of the most common nonidealities of class-E PAs: the limited loaded quality factor (Qloaded) of the series filter, switch on-resistance, the limited quality factor of the dc-feed inductor, load mismatch-dependent switch conduction loss, and the limited negative voltage excursions (due to, e.g., the reverse conduction of the switch transistor for negative voltage excursions). The theoretical findings are backed up by extensive circuit simulations and load-pull measurements of a class-E PA implemented in 65-nm CMOS technology. The PA provides 18.1-dBm output power and 72% efficiency at 1.4 GHz under nominal operating condition employing an off-chip matching network

A Millimeter-Wave Coexistent RFIC Receiver Architecture in 0.18-µm SiGe BiCMOS for Radar and Communication Systems

Innovative circuit architectures and techniques to enhance the performance of several key BiCMOS RFIC building blocks applied in radar and wireless communication systems operating at the millimeter-wave frequencies are addressed in this dissertation. The former encapsulates the development of an advanced, low-cost and miniature millimeter-wave coexistent current mode direct conversion receiver for short-range, high-resolution radar and high data rate communication systems. A new class of broadband low power consumption active balun-LNA consisting of two common emitters amplifiers mutually coupled thru an AC stacked transformer for power saving and gain boosting. The active balun-LNA exhibits new high linearity technique using a constant gm cell transconductance independent of input-outputs variations based on equal emitters’ area ratios. A novel multi-stages active balun-LNA with innovative technique to mitigate amplitude and phase imbalances is proposed. The new multi-stages balun-LNA technique consists of distributed feed-forward averaging recycles correction for amplitude and phase errors and is insensitive to unequal paths parasitic from input to outputs. The distributed averaging recycles correction technique resolves the amplitude and phase errors residuals in a multi-iterative process. The new multi-stages balun-LNA averaging correction technique is frequency independent and can perform amplitude and phase calibrations without relying on passive lumped elements for compensation. The multi-stage balun-LNA exhibits excellent performance from 10 to 50 GHz with amplitude and phase mismatches less than 0.7 dB and 2.86º, respectively. Furthermore, the new multi-stages balun-LNA operates in current mode and shows high linearity with low power consumption. The unique balun-LNA design can operates well into mm-wave regions and is an integral block of the mm-wave radar and communication systems. The integration of several RFIC blocks constitutes the broadband millimeter-wave coexistent current mode direct conversion receiver architecture operating from 22- 44 GHz. The system and architectural level analysis provide a unique understanding into the receiver characteristics and design trade-offs. The RF front-end is based on the broadband multi-stages active balun-LNA coupled into a fully balanced passive mixer with an all-pass in-phase/quadrature phase generator. The trans-impedance amplifier converts the input signal current into a voltage gain at the outputs. Simultaneously, the high power input signal current is channelized into an anti-aliasing filter with 20 dB rejection for out of band interferers. In addition, the dissertation demonstrates a wide dynamic range system with small die area, cost effective and very low power consumption

A Millimeter-Wave Coexistent RFIC Receiver Architecture in 0.18-µm SiGe BiCMOS for Radar and Communication Systems

Innovative circuit architectures and techniques to enhance the performance of several key BiCMOS RFIC building blocks applied in radar and wireless communication systems operating at the millimeter-wave frequencies are addressed in this dissertation. The former encapsulates the development of an advanced, low-cost and miniature millimeter-wave coexistent current mode direct conversion receiver for short-range, high-resolution radar and high data rate communication systems. A new class of broadband low power consumption active balun-LNA consisting of two common emitters amplifiers mutually coupled thru an AC stacked transformer for power saving and gain boosting. The active balun-LNA exhibits new high linearity technique using a constant gm cell transconductance independent of input-outputs variations based on equal emitters’ area ratios. A novel multi-stages active balun-LNA with innovative technique to mitigate amplitude and phase imbalances is proposed. The new multi-stages balun-LNA technique consists of distributed feed-forward averaging recycles correction for amplitude and phase errors and is insensitive to unequal paths parasitic from input to outputs. The distributed averaging recycles correction technique resolves the amplitude and phase errors residuals in a multi-iterative process. The new multi-stages balun-LNA averaging correction technique is frequency independent and can perform amplitude and phase calibrations without relying on passive lumped elements for compensation. The multi-stage balun-LNA exhibits excellent performance from 10 to 50 GHz with amplitude and phase mismatches less than 0.7 dB and 2.86º, respectively. Furthermore, the new multi-stages balun-LNA operates in current mode and shows high linearity with low power consumption. The unique balun-LNA design can operates well into mm-wave regions and is an integral block of the mm-wave radar and communication systems. The integration of several RFIC blocks constitutes the broadband millimeter-wave coexistent current mode direct conversion receiver architecture operating from 22- 44 GHz. The system and architectural level analysis provide a unique understanding into the receiver characteristics and design trade-offs. The RF front-end is based on the broadband multi-stages active balun-LNA coupled into a fully balanced passive mixer with an all-pass in-phase/quadrature phase generator. The trans-impedance amplifier converts the input signal current into a voltage gain at the outputs. Simultaneously, the high power input signal current is channelized into an anti-aliasing filter with 20 dB rejection for out of band interferers. In addition, the dissertation demonstrates a wide dynamic range system with small die area, cost effective and very low power consumption

EMC in Power Electronics and PCB Design

This dissertation consists of two parts. Part I is about Electromagnetic Compatibility (EMC) in power electronics and part II is about the Maximum Radiated Electromagnetic Emissions Calculator (MREMC), which is a software tool for EMC in printed circuit board (PCB) design. Switched-mode power converters can be significant sources of electromagnetic fields that interfere with the proper operation of nearby circuits or distant radio receivers. Part I of this dissertation provides comprehensive and organized information on the latest EMC developments in power converters. It describes and evaluates different technologies to ensure that power converters meet electromagnetic compatibility requirements. Chapters 2 and 3 describe EMC noise sources and coupling mechanisms in power converters. Chapter 4 reviews the measurements used to characterize and troubleshoot EMC problems. Chapters 5 - 8 cover passive filter solutions, active filter solutions, noise cancellation methods and reduced-noise driving schemes. Part II describes the methods used, calculations made, and implementation details of the MREMC, which is a software tool that allows the user to calculate the maximum possible radiated emissions that could occur due to specific source geometries on a PCB. Chapters 9 - 13 covers the I/O coupling EMI algorithm, Common-mode EMI algorithm, Power Bus EMI algorithm and Differential-Mode EMI algorithm used in the MREMC

High power high efficiency microwave power amplifier design using Class-E topology

Ankara : The Department of Electrical and Electronics Engineering and the Institute of Engineering and Sciences of Bilkent University, 2010.Thesis (Master's) -- Bilkent University, 2010.Includes bibliographical references leaves 65-67.Power consumption is a major problem in wireless technology. Since power ampli- fier is one of the most power consuming element, efficiency of the power amplifier should be optimized. Switching amplifiers typically offer very high efficiency. As the frequency increases, the efficiency drops. Class-E is a switching amplifier which is suitable for microwave frequencies. It attains a very high efficiency with proper voltage and current characteristics. Different techniques to obtain these characteristics are possible. In this work, we implement a 38 dBm power amplifier at 2 GHz. Different methods are examined to obtain a high efficiency behavior. We obtained a power added efficiency of 60%.Coşkun, Akif AlperenM.S