Nanoscale Electrodes by Conducting Atomic Force Microscopy: Oxygen Reduction Kinetics at the Pt|CsHSO_4 Interface

We quantitatively characterized oxygen reduction kinetics at the nanoscale Pt|CsHSO_4 interface at ~150 °C in humidified air using conducting atomic force microscopy (AFM) in conjunction with AC impedance spectroscopy and cyclic voltammetry. From the impedance measurements, oxygen reduction at Pt|CsHSO_4 was found to comprise two processes, one displaying an exponential dependence on overpotential and the other only weakly dependent on overpotential. Both interfacial processes displayed near-ideal capacitive behavior, indicating a minimal distribution in the associated relaxation time. Such a feature is taken to be characteristic of a nanoscale interface in which spatial averaging effects are absent and, furthermore, allows for the rigorous separation of multiple processes that would otherwise be convoluted in measurements using conventional macroscale electrode geometries. The complete current-voltage characteristics of the Pt|CsHSO_4 interface were measured at various points across the electrolyte surface and reveal a variation of the oxygen reduction kinetics with position. The overpotential-activated process, which dominates at voltages below -1 V, was interpreted as a charge-transfer reaction. Analysis of six different sets of Pt|CsHSO_4 experiments, within the Butler-Volmer framework, yielded exchange coefficients (α) for charge transfer ranging from 0.1 to 0.6 and exchange currents (i_0) spanning 5 orders of magnitude. The observed counter-correlation between the exchange current and exchange coefficient indicates that the extent to which the activation barrier decreases under bias (as reflected in the value of α) depends on the initial magnitude of that barrier under open circuit conditions (as reflected in the value of i_0). The clear correlation across six independent sets of measurements further indicates the suitability of conducting AFM approaches for careful and comprehensive study of electrochemical reactions at electrolyte-metal-gas boundaries

Electro-Oxidation of p-Silicon in Fluoride-Containing Electrolyte: A Physical Model for the Regime of Negative Differential Resistance

When Si is anodically oxidized in a fluoride containing electrolyte, an oxide layer is grown. Simultaneously, the layer is etched by the fluoride containing electrolyte. The resulting stationary state exhibits a negative slope of the current-voltage characteristics in a certain range of applied voltage. We propose a physical model that reproduces this negative slope. In particular, our model assumes that the oxide layer consists of both partially and fully oxidized Si and that the etch rate depends on the effective degree of oxidation. Finally, we show that our simulations are in good agreement with measurements of the current-voltage characteristics, the oxide layer thickness, the dissolution valence, and the impedance spectra of the electrochemical system.Comment: 19 pages, 13 figures, accepted for publication in EPJ S

A Cu\u3csub\u3e4\u3c/sub\u3eS Model for the Nitrous Oxide Reductase Active Sites Supported Only by Nitrogen Ligands

To model the (His)7Cu4Sn (n = 1 or 2) active sites of nitrous oxide reductase, the first Cu4(μ4-S) cluster supported only by nitrogen donors has been prepared using amidinate supporting ligands. Structural, magnetic, spectroscopic, and computational characterization is reported. Electrochemical data indicates that the 2-hole model complex can be reduced reversibly to the 1-hole state and irreversibly to the fully reduced state

Formation of Atomic-Sized Contacts by Electrochemical Methods

Electrochemical methods have recently become an interesting tool for fabricating and characterizing nanostructures at room temperature. Simplicity, low cost and reversibility are some of the advantages of this technique that allows to work at the nanoscale without requiring sophisticated instrumentation. In our experimental setup, we measure the conductance across a nanocontact fabricated either by dissolving a macroscopic gold wire or by depositing gold in between two separated gold electrodes. We have achieved a high level of control on the electrochemical fabrication of atomic-sized contacts in gold. The use of electrochemistry as a reproducible technique to prepare nanocontacts will open several possibilities that are not feasible with other methodologies. It involves, also, the possibility of reproducing experiments that today are made by more expensive, complicated or irreversible methods. As example, we show here a comparison of the results when looking for shell effects in gold nanocontacts with those obtained by other techniques.Comment: 7 pages, 5 figures, submitted to PS

Synthesis And Characterization Of (pyNO−)2GaCl: A Redox-Active Gallium Complex

We report the synthesis of a gallium complex incorporating redox-active pyridyl nitroxide ligands. The (pyNO−)2GaCl complex was prepared in 85% yield via a salt metathesis route and was characterized by 1H and 13C NMR spectroscopies, X-ray diffraction, and theory. UV–Vis absorption spectroscopy and electrochemistry were used to access the optical and electrochemical properties of the complex, respectively. Our discussion focuses primarily on a comparison of the gallium complex to the corresponding aluminum derivative and shows that although the complexes are very similar, small differences in the electronic structure of the complexes can be correlated to the identity of the metal

Electrochemical characterization of nanoporous nickel oxide thin films spray-deposited onto indium-doped tin oxide for solar conversion scopes

Nonstoichiometric nickel oxide (NiOx) has been deposited as thin film utilizing indium-doped tin oxide as transparent and electrically conductive substrate. Spray deposition of a suspension of nanoparticles in alcoholic medium allowed the preparation of uniform coatings. Sintering of the coatings was conducted at temperatures below 500°C for few minutes. This scalable procedure allowed the attainment of films with mesoporous morphology and reticulated structure. The electrochemical characterization showed that electrodes possess large surface area (about 1000 times larger than their geometrical area). Due to the openness of the morphology, the underlying conductive substrate can be contacted by the electrolyte and undergo redox processes within the potential range in which is electroactive. This requires careful control of the conditions of polarization in order to prevent the simultaneous occurrence of reduction/oxidation processes in both components of the multilayered electrode. The combination of the open structure with optical transparency and elevated electroactivity in organic electrolytes motivated us to analyze the potential of the spray-deposited films as semiconducting cathodes of dye-sensitized solar cells of p-type when erythrosine B was the sensitizer

Oxygen reduction at the silver/hydroxide-exchange membrane interface

A solid-state cell is used to study the electrocatalysis of oxygen reduction at the silver/hydroxide-exchange membrane interface. The catalyst/membrane interface exhibits improved performance in comparison to a catalyst/aqueous sodium hydroxide interface. Surprisingly, the half-wave potential for oxygen reduction is shown to shift 185 mV higher at the silver/hydroxide-exchange membrane interface than for the silver/aqueous hydroxide solution interface, and the exchange current density is significantly higher at 1.02 × 10−6 A m−2. On a cost per performance basis, silver electrocatalysts in a hydroxide-exchange membrane fuel cell may provide better performance than platinum in a proton-exchange membrane fuel cell. Keywords: Oxygen reduction reaction, Electrocatalyst, Alkaline membrane, Solid-state cell, Silve

Elaboration of integrated microelectrodes for the detection of antioxidant species

(Pt–Pt–Ag/AgCl) and (Au–Pt–Ag/AgCl) electrochemical microcells (ElecCell) were developed for the detection of redox species by cyclic voltammetry. A special emphasis was placed on the SU-8 waferlevel passivation process in order to optimize the electrochemical properties of the different “thin film” metallic layers, i.e. gold or platinum for the working electrode, platinum for the counter electrode and silver/silver chloride for the reference electrode. (Au–Pt–Ag/AgCl) microcells were applied for the detection of antioxidant species such as ascorbic and uric acids in phosphate buffer solution, evidencing high sensitivity but low selectivity. Works were extended to skin analysis, demonstrating that a good electrical contact with the skin hydrolipidic film allowed the effective evaluation of the skin global antioxidant capacity

Photoelectrochemical properties of mesoporous NiOx deposited on technical FTO via nanopowder sintering in conventional and plasma atmospheres

Nanoporous nickel oxide (NiO x ) has been deposited with two different procedures of sintering (CS and RDS). Both samples display solid state oxidation at about 3.1 V vs Li+/Li. Upon sensitization of CS/RDS NiO x with erythrosine b (ERY), nickel oxide oxidation occurs at the same potential. Impedance spectroscopy revealed a higher charge transfer resistance for ERY-sensitized RDS NiO x with respect to sensitized CS NiO x . This was due to the chemisorption of a larger amount of ERY on RDS with respect to CS NiO x . Upon illumination the photoinduced charge transfer between ERY layer and NiO x could be observed only with oxidized CS. Photoelectrochemical effects of sensitized RDS NiO x were evidenced upon oxide reduction. With the addition of iodine RDS NiOx electrodes could give the reduction iodine → iodide in addition to the reduction of RDS NiO x . p-type dye sensitized solar cells were assembled with RDS NiO x photocathodes sensitized either by ERY or Fast Green. Resulting overall efficiencies ranged between 0.02 and 0.04 % upon irradiation with solar spectrum simulator (Iin : 0.1 W cm −2 )