Experimental evidence of flow destabilization in a 2D bidisperse foam

Liquid foam flows in a Hele-Shaw cell were investigated. The plug flow obtained for a monodisperse foam is strongly perturbed in the presence of bubbles whose size is larger than the average bubble size by an order of magnitude at least. The large bubbles migrate faster than the mean flow above a velocity threshold which depends on its size. We evidence experimentally this new instability and, in case of a single large bubble, we compare the large bubble velocity with the prediction deduced from scaling arguments. In case of a bidisperse foam, an attractive interaction between large bubbles induces segregation and the large bubbles organize themselves in columns oriented along the flow. These results allow to identify the main ingredients governing 2D polydisperse foam flows

Flow of foam through plain perforated and woven metal screens

The interaction of foam with textile substrates has been investigated, starting with an attempt to describe the flow of foam in textile–like substrates. This was done by separately evaluating rheology and pressure–drop data. The influence of bubble size was found to be particularly important. In a coaxial cylinder viscometer the viscosity was found to be inversely proportional to bubble size. This finding could not be used to describe the pressure drop of foam flow through flat metal screens according to the d'Arcy equation. Equations could not be satisfactorily derived to describe phenomena such as bubble deformation and diminution, but empirical determination of these parameters could be achieved for each combination of foam and substrate

Novel thick-foam ferroelectret with engineered voids for energy harvesting applications

This work reports a novel thick-foam ferroelectret which is designed and engineered for energy harvesting applications. We fabricated this ferroelectret foam by mixing a chemical blowing agent with a polymer solution, then used heat treatment to activate the agent and create voids in the polymer foam. The dimensions of the foam, the density and size of voids can be well controlled in the fabrication process. Therefore, this ferroelectret can be engineered into optimized structure for energy harvesting applications

Mechanical probing of liquid foam aging

We present experimental results on the Stokes experiment performed in a 3D dry liquid foam. The system is used as a rheometric tool : from the force exerted on a 1cm glass bead, plunged at controlled velocity in the foam in a quasi static regime, local foam properties are probed around the sphere. With this original and simple technique, we show the possibility of measuring the foam shear modulus, the gravity drainage rate and the evolution of the bubble size during coarsening

Dissipative flows of 2D foams

We analyze the flow of a liquid foam between two plates separated by a gap of the order of the bubble size (2D foam). We concentrate on the salient features of the flow that are induced by the presence, in an otherwise monodisperse foam, of a single large bubble whose size is one order of magnitude larger than the average size. We describe a model suited for numerical simulations of flows of 2D foams made up of a large number of bubbles. The numerical results are successfully compared to analytical predictions based on scaling arguments and on continuum medium approximations. When the foam is pushed inside the cell at a controlled rate, two basically different regimes occur: a plug flow is observed at low flux whereas, above a threshold, the large bubble migrates faster than the mean flow. The detailed characterization of the relative velocity of the large bubble is the essential aim of the present paper. The relative velocity values, predicted both from numerical and from analytical calculations that are discussed here in great detail, are found to be in fair agreement with experimental results

Large strain compressive response of 2-D periodic representative volume element for random foam microstructures

A numerical investigation has been conducted to determine the influence of Representative Volume Element (RVE) size and degree of irregularity of polymer foam microstructure on its compressive mechanical properties, including stiffness, plateau stress and onset strain of densification. Periodic two-dimensional RVEs have been generated using a Voronoi-based numerical algorithm and compressed. Importantly, self-contact of the foam’s internal microstructure has been incorporated through the use of shell elements, allowing simulation of the foam well into the densification stage of compression; strains of up to 80 percent are applied. Results suggest that the stiffness of the foam RVE is relatively insensitive to RVE size but tends to soften as the degree of irregularity increases. Both the shape of the plateau stress and the onset strain of densification are sensitive to both the RVE size and degree of irregularity. Increasing the RVE size and decreasing the degree of irregularity both tend to result in a decrease of the gradient of the plateau region, while increasing the RVE size and degree of irregularity both tend to decrease the onset strain of densification. Finally, a method of predicting the onset strain of densification to an accuracy of about 10 per cent, while reducing the computational cost by two orders of magnitude is suggested

High strength, medium density molded foam

Toluene diisocyanate-based polyurethane produces molded-to-size foam products. Formulation techniques optimize dimension stability, strength and moldability

Ocean foam generation and modeling

A laboratory investigation was conducted to determine the physical and microwave properties of ocean foam. Special foam generators were designed and fabricated, using porous glass sheets, known as glass frits, as the principal element. The glass frit was sealed into a water-tight vertical box, a few centimeters from the bottom. Compressed air, applied to the lower chamber, created ocean foam from sea water lying on the frit. Foam heights of 30 cm were readily achieved, with relatively low air pressures. Special photographic techniques and analytical procedures were employed to determine foam bubble size distributions. In addition, the percentage water content of ocean foam was determined with the aid of a particulate sampling procedure. A glass frit foam generator, with pore diameters in the range 70 - 100 micrometers, produced foam with bubble distributions very similar to those found on the surface of natural ocean foam patches