73 research outputs found

    Combustion stability limits of coflowing turbulent jet diffusion flames

    Full text link
    Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/76288/1/AIAA-1988-538-444.pd

    ICEF2004-960 MICROPHONES AND KNOCK SENSORS FOR FEEDBACK CONTROL OF HCCI ENGINES

    Get PDF
    ABSTRACT Homogeneous charge compression ignition (HCCI) engines lack direct in-cylinder CA50 engine crank position in CAD at 50% heat release CAD crank angle degrees HCCI homogeneous charge compression ignition µ sample mean ∇ differencing operator, ∇Y t = Y t −Y t−1 P t predicted (at engine position t) value of a series φ fuel-air equivalence ratio PID proportional-integral-derivative control law RPM revolutions per minute SI spark-ignited TDC top-dead-center of the compression stroke V voltage Y t time t values of data series WN(µ,σ 2 ) normally-distributed white noise process with mean µ and variance σ

    The Effect of the Di-Tertiary Butyl Peroxide (DTBP) additive on HCCI Combustion of Fuel Blends of Ethanol and Diethyl Ether

    Full text link
    The influence of the small amounts (1-3%) of the additive di-tertiary butyl peroxide (DTBP) on the combustion event of Homogeneous Charge Compression Ignition (HCCI) engines was investigated using engine experiments, numerical modeling, and carbon-14 isotope tracing. DTBP was added to neat ethanol and diethyl ether (DEE) in ethanol fuel blends for a range of combustion timings and engine loads. The addition of DTBP to the fuel advanced combustion timing in each instance, with the DEE-in-ethanol mixture advancing more than the ethanol alone. A numerical model reproduced the experimental results. Carbon-14 isotope tracing showed that more ethanol burns to completion in DEE-in-ethanol blends with a DTBP additive when compared to results for DEE-in-ethanol without the additive. However, the addition of DTBP did not elongate the heat release in either case. The additive advances combustion timing for both pure ethanol and for DEE-in-ethanol mixtures, but the additive results in more of an advance in timing for the DEE-in-ethanol mixture. This suggests that although there are both thermal and kinetic influences from the addition of DTBP, the thermal effects are more important

    Numerical and experimental study of water/oil emulsified fuel combustion in a diesel engine

    No full text
    Numerical and experimental studies were made on some of the chemical and physical properties of wateržoil emulsified fuel (W/OEF) combustion characteristics. Numerical investigations of W/OEF combustion\u27s chemical kinetic aspects have been performed by simulation of water/n-heptane mixture combustion, assuming a model of a homogenous reactor\u27s concentric shells. The injection and fuel spray characteristics are analyzed numerically also in order to study indirectly the physical effects of water present in diesel fuel during the combustion process. The experimental results of W/OEF combustion in the DI diesel engine are also presented and discussed. The results of engine testing in a broad field of engine loads and speeds have shown a significant pollutant emission reduction with no worsening of specific fuel consumption

    Effect of hydrogen peroxide addition to methane fueled homogeneous charge compression ignition engines through numerical simulations

    No full text
    The effect of the direct injection of hydrogen peroxide into a port-injected methane fueled homogeneous charge compression ignition engine was investigated numerically. The injection of aqueous hydrogen peroxide was implemented as a means of combustion phasing control. A single cylinder homogeneous charge compression ignition engine (2.43 L Caterpillar) was modeled using the Cantera 2.0 flame code toolkit, the GRI-Mech 3.0 chemical reaction mechanism, and a single-zone slider-crank engine model. Start of injection timing and the amount of injected hydrogen peroxide were manipulated to achieve desired combustion phasing under a wide range of intake temperatures. As the concentration of hydrogen peroxide is increased, the combustion phasing is advanced up to 22 degrees for the conditions investigated in this study. This advancing effect is most pronounced at small concentrations (< 10 g H2O2 / kg CH4) and early injection timings (SOI < 25 degrees BTDC). The model suggests hydrogen peroxide can be introduced as a means of combustion phasing control while maintaining the low emissions and peak in-cylinder pressures inherent in homogeneous charge compression ignition engines

    Iván D Exploring Strategies for Reducing High Intake Temperature Requirements and Allowing Optimal Operational Conditions in a Biogas Fueled HCCI Engine for Power Generation

    No full text
    This paper evaluates strategies for reducing the intake temperature requirement for igniting biogas in homogeneous charge compression ignition (HCCI) engines. The HCCI combustion is a promising technology for stationary power generation using renewable fuels in combustion engines. Combustion of biogas in HCCI engines allows high thermal efficiency similar to diesel engines, with low net CO 2 and low NO x emissions. However, in order to ensure the occurrence of autoignition in purely biogas fueled HCCI engines, a high inlet temperature is needed. This paper presents experimental and numerical results. First, the experimental analysis on a 4 cylinder, 1.9 L Volkswagen TDI diesel engine running with biogas in the HCCI mode shows high gross indicated mean effective pressure (close to 8 bar), high gross indicated efficiency (close to 45%) and NO x emissions below the 2010 US limit (0.27 g/kWh). Stable HCCI operation is experimentally demonstrated with a biogas composition of 60% CH 4 and 40% CO 2 on a volumetric basis, inlet pressures of 2-2.2 bar (absolute), and inlet temperatures of 200-210 C for equivalence ratios between 0.19-0.29. At lower equivalence ratios, slight changes in the inlet pressure and temperature caused large changes in cycle-to-cycle variations, while at higher equivalence ratios these same small pressure and temperature variations caused large changes to the ringing intensity. Second, numerical simulations have been carried out to evaluate the effectiveness of high boost pressures and high compression ratios for reducing the inlet temperature requirements while attaining safe operation and high power output. The one zone model in Chemkin was used to evaluate the ignition timing and peak cylinder pressures with variations in temperatures at intake valve close (IVC) from 373 to 473 K. In-cylinder temperature profiles between IVC and ignition were computed using Fluent 6.3 and fed into the multizone model in Chemkin to study combustion parameters. According to the numerical results, the use of both higher boost pressures and higher compression ratios permit lower inlet temperatures within the safe limits experimentally observed and allow higher power output. However, the range of inlet temperatures allowing safe and efficient operation using these strategies is very narrow, and precise inlet temperature control is needed to ensure the best results
    • …
    corecore