422 research outputs found
An increase of a down-hole nuclear magnetic resonance tool’s reliability and accuracy by the cancellation of a multi-module DC/AC converter's output’s higher harmonics
Abstract: Described in this paper is a method for improving higher harmonic cancellation in Nuclear Magnetic Resonance (NMR) transmitters, which are used in oil and gas well logging tools operating at 175°C. Multi-module multi-level topology which combines the outputs of several identical power modules operating at 50% duty cycle at the fundamental frequency provide the versatility needed for both low harmonic sine voltage synthesis and amplitude control. Cancellation of the output voltage higher harmonics is achieved by creating fixed relative phase shifts between the individual modules of the multi-module converter. The amplitude control employs the Chireix-Doherty outphasing modulation principle with added feed forward correction circuitry. The possibilities of a 20% increase of the tool signal to noise ratio (SNR), as compared to that of a two-module transmitter has also demonstrated significant increase in the tool life expectancy
Simulation of Processes in Dual Three-Phase System on the Base of Four Inverters with Synchronized Modulation
Novel method of space-vector-based pulse-width modulation (PWM) has been disseminated for synchronous control of four inverters feeding six-phase drive on the base of asymmetrical induction motor which has two sets of windings spatially shifted by 30 electrical degrees. Basic schemes of synchronized PWM, applied for control of four separate voltage-source inverters, allow both continuous phase voltages synchronization in the system and required power sharing between DC sources. Detailed MATLAB-based simulations show a behavior of six-phase system with continuous and discontinuous versions of synchronized PWM
A multistage DC-DC step-up self-balanced and magnetic component-free converter for photovoltaic applications : hardware implementation
Abstract: This article presents a self-balanced multistage DC-DC step-up converter for photovoltaic applications. The proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (transformer-less and inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. 2 K diodes and 2 K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K + 1) times the input voltage. The conspicuous features of proposed topology are: (i) magnetic component free (transformer-less and inductor-less); (ii) continuous input current; (iii) low voltage rating semiconductor devices and capacitors; (iv) modularity; (v) easy to add a higher number of levels to increase voltage gain; (vi) only two control switches with alternating operation and simple control. The proposed converter is compared with recently described existing transformer-less and inductor-less power converters in term of voltage gain, number of devices and cost. The application of the proposed circuit is discussed in detail. The proposed converter has been designed with a rated power of 60 W, input voltage is 24 V, output voltage is 100 V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results
Development of Sliding Mode Controller for a Modified Boost Cuk Converter Configuration
This paper introduces a sliding mode control (SMC)-based equivalent control method to a novel high output gain Ćuk converter. An additional inductor and capacitor improves the efficiency and output gain of the classical Ćuk converter. Classical proportional integral (PI) controllers are widely used in direct current to direct current (DC-DC) converters. However, it is a very challenging task to design a single PI controller operating in different loads and disturbances. An SMC-based equivalent control method which achieves a robust operation in a wide operation range is also proposed. Switching frequency is kept constant in appropriate intervals at different loading and disturbance conditions by implementing a dynamic hysteresis control method. Numerical simulations conducted in MATLAB/Simulink confirm the accuracy of analysis of high output gain modified Ćuk converter. In addition, the proposed equivalent control method is validated in different perturbations to demonstrate robust operation in wide operation range
Lyapunov based reference model of tension control in a continuous strip processing line with multi-motor drive
The article describes design and experimental verification of a new control structure with reference model for a multi-motor drive of a continuous technological line in which the motors are mutually mechanically coupled through processed material. Its principle consists in creating an additional information by introducing a new suitable state variable into the system. This helps to achieve a zero steady-state control deviation of the tension in the strip. Afterwards, the tension controller is designed to ensure asymptotic stability of the extended system by applying the second Lyapunov method. The realized experimental measurements performed on a continuous line laboratory model confirm the advantages and correctness of the proposed control structure: it is simple, stable, robust against changes of parameters, invariant to operating disturbances and ensures a high-quality dynamics of the controlled system prescribed by the reference model. To demonstrate effectiveness of the design, the performance of the controller was compared with properties of a standard Proportional Integral Derivative/Proportional Integral (PID/PI) controller designed in frequency domain
- …