1,070 research outputs found
Femoral lengthening with a rail external fixator: tips and tricks
Lengthening the femur with an external fixator is commonly practised for a wide variety of pathologies. This technical report includes tips derived from observation and experience in a busy limb reconstruction unit. It focuses on the use of a rail fixator, although some of the descriptions are applicable to lengthening by circular fixators
Scientific support for an orbiter middeck experiment on solid surface combustion
The objective is to determine the mechanism of gas-phase flame spread over solid fuel surfaces in the absence of any buoyancy or externally imposed gas-phase flow. Such understanding can be used to improve the fire safety aspects of space travel by providing information that will allow judicious selections of spacecraft materials and environments to be made. The planned experiment consists of measuring the flame spread rate over thermally thin and thermally thick fuels in a closed container in the low-gravity environment of the Space Shuttle. Measurements consist of flame spread rate and shape obtained from two views of the process as recorded on movie film and surface and gas-phase temperatures obtained from fine-wire thermocouples. The temperature measurements along with appropriate modeling provide information about the gas-to-solid heat flux. Environmental parameters to be varied are the oxygen concentration and pressure
Pattern Formation in Diffusion Flames Embedded in von Karman Swirling Flows
Pattern formation is observed in nature in many so-called excitable systems that can support wave propagation. It is well-known in the field of combustion that premixed flames can exhibit patterns through differential diffusion mechanism between heat and mass. However, in the case of diffusion flames where fuel and oxidizer are separated initially there have been only a few observations of pattern formation. It is generally perceived that since diffusion flames do not possess an inherent propagation speed they are static and do not form patterns. But in diffusion flames close to their extinction local quenching can occur and produce flame edges which can propagate along stoichiometric surfaces. Recently, we reported experimental observations of rotating spiral flame edges during near-limit combustion of a downward-facing polymethylmethacrylate disk spinning in quiescent air. These spiral flames, though short-lived, exhibited many similarities to patterns commonly found in quiescent excitable media including compound tip meandering motion. Flame disks that grow or shrink with time depending on the rotational speed and in-depth heat loss history of the fuel disk have also been reported. One of the limitations of studying flame patterns with solid fuels is that steady-state conditions cannot be achieved in air at normal atmospheric pressure for experimentally reasonable fuel thickness. As a means to reproduce the flame patterns observed earlier with solid fuels, but under steady-state conditions, we have designed and built a rotating, porous-disk burner through which gaseous fuels can be injected and burned as diffusion flames. The rotating porous disk generates a flow of air toward the disk by a viscous pumping action, generating what is called the von K rm n boundary layer which is of constant thickness over the entire burner disk. In this note we present a map of the various dynamic flame patterns observed during the combustion of methane in air as a function of fuel flow rate and the burner rotational speed
The pelvic support osteotomy: indications and preoperative planning
The pelvic support osteotomy is a double level femoral osteotomy with the objective of eliminating a Trendelenburg and short limb gait in young patients with severe hip joint destruction as a consequence of neonatal septic arthritis. The osteotomy has seen several changes and a brief historical overview is provided to set the evolution of the modifications of the procedure in context. We present an analysis of the preoperative assessment that will assist the surgeon to plan out the procedure. Specifically, we set out to answer the following questions: (a) Where should the first osteotomy be performed and what is the magnitude of valgus and extension correction desired at this level? (b) Where should the second osteotomy be performed and what is the magnitude of varus and derotation desired at this level
Droplet Combustion Experiment
Liquid fuel combustion provides a major portion of the world's energy supply. In most practical combustion devices, liquid burns after being separated into a droplet spray. Essential to the design of efficient combustion systems is a knowledge of droplet combustion behavior. The microgravity environment aboard spacecraft provides an opportunity to investigate the complex interactions between the physical and chemical combustion processes involved in droplet combustion without the complications of natural buoyancy. Launched on STS-83 and STS-94 (April 4 and July 1, 1997), the Droplet Combustion Experiment (DCE) investigated the fundamentals of droplet combustion under a range of pressures (0.25 to 1 atm), oxygen mole fractions (<0.5), and droplet sizes (1.5 to 5 mm). Principal DCE flight hardware features were a chamber to supply selected test environments, the use of crew-inserted bottles, and a vent system to remove unwanted gaseous combustion products. The internal apparatus contained the droplet deployment and ignition mechanisms to burn single, freely deployed droplets in microgravity. Diagnostics systems included a 35-mm high-speed motion picture camera (see the following sequence of photos) with a backlight to photograph burning droplets and a camcorder to monitor experiment operations. Additional diagnostics included an ultraviolet-light-sensitive CCD (charge couple discharge) camera to obtain flame radiation from hydroxyl radicals (see the final figure) and a 35-mm SLR (single-lens-reflex) camera to obtain color still photographs of the flames
Awareness and knowledge of diabetes mellitus among diabetic patients in Puducherry, India
Background: Diabetes prevalence is high in India and the numbers are increasing every year. Many patients are aware that they have diabetes only when they develop one of its complications. Since there is a paucity of literature on the level of awareness and knowledge about diabetes, this study was done.Methods: It is a cross-sectional study conducted on diabetic patients attending Sri Lakshmi Narayana Institute of Medical Sciences and Hospital, Puducherry over a period of two months, using questionnaire. The demographic data were analyzed using descriptive statistics. Quantitative data were expressed as percentages.Results: Among 104 diabetics, 60%, 49% and 66% of the patients answered high sugar intake as the cause of diabetes, loss of vision as its complication and diet control as the important measure of treatment of diabetes respectively. Only 30.67% of the patients were aware of the name of the medicine they consume.Conclusions: Awareness and knowledge about diabetes were less in our study populations. Hence it is important to extend the diabetic health programs in mass campaigns to improve their knowledge
- …