336 research outputs found

    Flexible power converters for the fault tolerant operation of Micro-Grids

    Get PDF
    The progressive penetration level of Distributed Generation (DG) is destined to cause deep changes in the existing distribution networks no longer considered as passive terminations of the whole electrical system. A possible solution is the realization of small networks, namely the Micro-Grids, reproducing in themselves the structure of the main production and distribution of the electrical energy system. In order to gain an adequate reliability level of the microgrids the individuation and the management of the faults with the goal of maintaining the micro-grid operation (fault tolerant operation) is quite important. In the present paper flexible power converters and a companion control algorithm for the fault tolerant operation of microgrids are presented. The effectiveness of such an algorithm and of the fault tolerant power converters are verified through computer simulations

    A procedure to calculate the I–V characteristics of thin-film photovoltaic modules using an explicit rational form

    Get PDF
    Accurate models of the electrical behaviour of photovoltaic modules are effective tools for system design. One or two diode equivalent circuits have been widely used even though some mathematical difficulties were found dealing with implicit equations. In this paper, a new model based on a simple rational function, which does not contain any implicit exponential form, is presented. The model was conceived in order to be used with thin-film photovoltaic modules, whose current–voltage curves are characterised by very smooth shapes. The parameters of the model are evaluated by means of the derivatives of the issued characteristics in the short circuit and open circuit points at standard rating conditions, and assuming that the calculated current–voltage curve contains the rated maximum power point of the simulated panel. The capability of the model to calculate the current–voltage characteristic for values of the solar irradiance and cell temperature far from the standard rating conditions was verified for various thin-film technologies, such as CIS, CIGS, amorphous silicon, tandem and triple-junctions photovoltaic modules. A comparison with the results obtained by another rational model and other two-diode models, which were used to simulate the electrical behaviour of thin-film photovoltaic modules, is also presented

    Performances of rainfall energy harvester

    Get PDF
    In this paper the performances of rainfall energy harvesting by means of piezoelectric transducers is presented. Diverse studies agree on the level of suitable generated voltage on the electrodes of a piezoelectric transducer subjected to rainfall, but a complete characterization on the supplied power is still missing. This work, in order to limit optimistic forecasts, takes into account the behavior of the transducers subjected to real and also artificial rainfall, condition that has shown promising behavior in laboratory. In order to increase the energy harvesting and also define its limits different loads have been taken into account. Only commercial transducers have been considered: a lead zirconate titanate and polyvinylidene difluoride transducer

    Analytical Investigation and Control System Set-up of Medium Scale PV Plants for Power Flow Management

    Get PDF
    In the field of photovoltaic (PV) plants and energy conversion from renewable sources, a large part of the technical literature is more devoted to practical aspects (new solar cells, electrically driven PV panels, safety, reduction of parasitic currents, etc.) than to theoretical investigations. Despite this tendency, this paper presents a mathematical analysis of a medium scale photovoltaic power generation system connected to the distribution network and of its control system. In such a system, the conversion stage is unique due to the absence of a boost chopper. The conducted analysis leads to the interesting conclusion that the inverter used in the plant presents two degrees of freedom, easy to exploit in a control system in which the inverter simultaneously realizes the interconnection to the grid and the MPPT control. The structure of the control system is then presented, discussed and validated by means of numerical simulations

    Main Fuel Cells mathematical models: Comparison and analysis in terms of free parameters

    Get PDF
    This paper resumes the main mathematical models of Fuel Cells (PEM models). In particular, a comparison study of the various models introduced in the technical literature is presented and the dependency of the various model parameters is analyzed in different operating conditions. As the manifold of the model parameter is very wide and their determination is difficult, it is mandatory to introduce approximations and simplifications on which each model is based. The novelty of this work is the organization of the existing models in three categories with regard to the number of free parameters and to the dependency of such parameters on the different running conditions and the usage of a reference model in order to compare the difference between the latter once both in terms of fast execution of the simulation and care of the simulation results

    A modular approach in teaching thyristor rectifiers with equation-oriented softwares

    Get PDF
    This article is devoted to some issues of teaching power electronics in university courses. In the modern education system the students are expected to be no longer subject of passive learning, but that, within a certain extent, they collaborate in their training interactively with the teacher to develop the applications and the topics of the studied framework. For this purpose, this article presents a modular approach for teaching module regarding three-phase thyristor rectifiers

    A Software for the Evaluation of Winding Factor Harmonic Distribution in High Efficiency Electrical Motors and Generators.

    Get PDF
    In this paper a software developed for the determination of winding connections, the calculation of winding factors and the evaluation of their harmonic distribution of three and two phase windings is presented by using as input data simply the number of slots, pole pairs and phases. The software is implemented as a function in MATLAB environment. By means of some examples, covering the most relevant winding types, the capabilities of this software will be shown. Particularly, integer and fractional single and double layer winding can be treated. Some examples are presented and briefly discussed. The connections, the winding factor harmonic distribution, the electro-motive force (e.m.f) THD calculations results are shown together with an example on how is possible to determine the e.m.f. induced in a winding from the air gap flux distribution and to estimate the differential leakage inductance

    Controlled Fault-Tolerant Power Converters for Power Quality Enhancement

    Get PDF
    Power quality depends generally on the interaction of electrical power with electrical equipments. If electrical equipments operate correctly and reliably without being damaged or stressed, a suitable level of power quality is assured. On the other hand, if the electrical equipment malfunctions, is unreliable, or is damaged during normal usage, power quality is poor and probably the economical loss could be important like the technical one. In the scenario of the Distributed Generation, power quality issues will be moreover important because an higher dissemination of power conditioning equipment will be requested and this obviously increases the sources of vulnerability of the electrical system. In this paper fault tolerant power converters are considered as a viable solution of power quality problems and a suitable control algorithm of them is presented. The control proposed in the paper is based on the model of the power converter reformulated in terms of healthy leg binary variable and the paper shows how this control is able to save the aspect of power quality when the converter works in the linear range. The effectiveness of such an algorithm and of the fault tolerant power converters are finally verified by means of simulations

    Piezoelectric model of rainfall energy harvester

    Get PDF
    In this paper a model to predict the harvest of the energy contained in rainfall by means of piezoelectric transducers is presented. Different studies agree on the level of suitable generated voltage on the electrodes of a piezoelectric transducer subjected to rainfall, but a complete characterization on the supplied power is still missing. This work, in order to limit optimistic forecasts, compares the behavior of the transducers subjected to real and artificial rainfall, a condition that has shown promising behavior in laboratory

    Analysis, characterization and minimization of IPMSMs cogging torque with different rotor structures

    Get PDF
    This paper presents the analysis, characterization and comparison of the cogging torque components generated by five different IPMSM rotor structures. More in detail, an IPMSM model (named IPMSM1), which is derived from a commercial geometry, is analyzed by using a Finite Element Method (FEM) approach. Then, four other IPMSM models, which are obtained by modifying the IPMSM1 rotor structure and by maintaining the same stator configuration, are proposed and analyzed. From the obtained simulation results, the cogging torque components for each structure are determined and compared. From this comparison, a significant cogging torque decrease is occurring for the modified geometries, without affecting the values of the generated torque. Furthermore, a meaningful relationship between the peak values of the cogging torque and the gradients of the flux density around the neutral area is reported and discussed. Therefore, simple structure modifications applied to the rotor geometry can bring significant improvements in terms of motor performances and cogging torque reductio
    • …
    corecore