Development of an electrochemical micromachining (μECM) machine

This thesis was submitted for the award of Doctor of Philosophy and was awarded by Brunel University London.Electrochemical machining (ECM) and especially electrochemical micromachining (μECM) became an attractive area of research due to the fact that this process does not create any defective layer after machining and that there is a growing demand for better surface integrity on different micro applications such as microfluidics systems and stressfree drilled holes in the automotive and aerospace sectors. Electrochemical machining is considered as a non-conventional machining process based on the phenomenon of electrolysis. This process requires maintaining a small gap - the interelectrode gap (IEG) - between the anode (workpiece) and the cathode (tool-electrode) in order to achieve acceptable machining results (i.e. accuracy, high aspect ratio with appropriate material removal rate and efficiency). This work presents the design of a next generation μECM machine for the automotive, aerospace, medical and metrology sectors. It has 3 axes of motion (X, Y and Z) and a spindle allowing the tool-electrode to rotate during machining. The linear slides for each axis use air bearings with linear DC brushless motors and 2nmresolution encoders for ultra-precise motion. The control system is based on the Power PMAC motion controller from Delta Tau. The electrolyte tank is located at the rear of the machine and allows the electrolyte to be changed quickly. A pulse power supply unit (PSU) and a special control algorithm have been implemented. The pulse power supply provides not only ultra-short pulses (50ns), but also plus and minus biases as well as a polarity switching functionality. It fulfils the requirements of tool preparation with reversed ECM on the machine. Moreover, the PSU is equipped with an ultrafast over current protection which prevents the tool-electrode from being damaged in case of short-circuits. Two different process control algorithms were made: one is fuzzy logic based and the other is adapting the feed rate according to the position and time at which short-circuits were detected. The developed machine is capable of drilling micro holes in hard-to-machine materials but also machine micro-styli and micro-needles for the metrology (micro CMM) and medical sectors. This work also presents drilling trials performed with the machine with an orbiting tool. Machining experiments were also carried out using electrolytes made of a combination of HCl and NaNO aqueous solutions. The developed machine was used to fabricate micro tools out of 170μm WC-Co alloy shafts via micro electrochemical turning and drill deep holes via μECM in disks made of 18NiCr6 alloy. Results suggest that this process can be used for industrial applications for hard-to-machine materials. The author also suggests that the developed machine can be used to manufacture micro-probes and micro-tools for metrology and micro-manufacturing purposes.Brunel University European Commissio

Design of an electrochemical micromachining machine

Electrochemical micromachining (μECM) is a non-conventional machining process based on the phenomenon of electrolysis. μECM became an attractive area of research due to the fact that this process does not create any defective layer after machining and that there is a growing demand for better surface integrity on different micro applications including microfluidics systems, stress-free drilled holes in automotive and aerospace manufacturing with complex shapes, etc. This work presents the design of a next generation μECM machine for the automotive, aerospace, medical and metrology sectors. It has three axes of motion (X, Y, Z) and a spindle allowing the tool-electrode to rotate during machining. The linear slides for each axis use air bearings with linear DC brushless motors and 2-nm resolution encoders for ultra precise motion. The control system is based on the Power PMAC motion controller from Delta Tau. The electrolyte tank is located at the rear of the machine and allows the electrolyte to be changed quickly. This machine features two process control algorithms: fuzzy logic control and adaptive feed rate. A self-developed pulse generator has been mounted and interfaced with the machine and a wire ECM grinding device has been added. The pulse generator has the possibility to reverse the pulse polarity for on-line tool fabrication.The research reported in this paper is supported by the European Commission within the project “Minimizing Defects in Micro-Manufacturing Applications (MIDEMMA)” (FP7-2011-NMPICT- FoF-285614)

Design of a pulse power supply unit for micro-ECM

Electrochemical micro-machining (μECM) requires a particular pulse power supply unit (PSU) to be developed in order to achieve desired machining performance. This paper summarises the development of a pulse PSU meeting the requirements of μECM. The pulse power supply provides tens of nanosecond pulse duration, positive and negative bias voltages and a polarity switching functionality. It fulfils the needs for tool preparation with reversed pulsed ECM on the machine. Moreover, the PSU is equipped with an ultrafast overcurrent protection which prevents the tool electrode from being damaged in case of short circuits. The developed pulse PSU was used to fabricate micro-tools out of 170 μm WC-Co alloy shafts via micro-electrochemical turning and drill deep holes via μECM in a disk made of 18NiCr6. The electrolyte used for both processes was a mixture of sulphuric acid and NaNO3 aqueous solutions.The research reported in this paper is supported by the European Commission within the project “Minimizing Defects in Micro-Manufacturing Applications (MIDEMMA)” (FP7-2011-NMP-ICT-FoF-285614

Rheology of cellulose nanofibrils and silver nanowires for the development of screen-printed antibacterial surfaces

TEMPO (2,2,6,6-tetramethylpiperidine-N-oxyl)-oxidized cellulose nanofibrils (T-CNF) and silver nanowires (Ag NWs) were formulated as active inks. Their rheological properties were investigated to design optimal conditions for processing by the screen-printing process, with the aim of preparing antibacterial patterns. Rheological experiments mimicking the screen-printing process were applied to different ink formulations to investigate their thixotropic and viscosity properties. The experiments conducted at 1wt% total mass content and different ratios of T-CNF/Ag NWs showed that the recovery (%), the recovery time and the viscosity are formulation dependent. A ratio 2:1 (T-CNF/Ag NWs) and total mass content of 2.5wt% were then selected to prepare an ink suitable for screen printing. Printing defects were corrected by addition of water-soluble polymer hydroxypropyl methylcellulose (HPMC). The selected formulation printed on flexible polyethylene terephthalate (PET) substrate displayed a 67.4% antibacterial activity against E. coli in a standard contact active test, with a transparency superior to 70%, proving the promising features of the developed solution for active packaging applications