10,503 research outputs found

    High Dynamic Range RF Front End with Noise Cancellation and Linearization for WiMAX Receivers

    Get PDF
    This research deals with verification of the high dynamic range for a heterodyne radio frequency (RF) front end. A 2.6 GHz RF front end is designed and implemented in a hybrid microwave integrated circuit (HMIC) for worldwide interoperability for microwave access (WiMAX) receivers. The heterodyne RF front end consists of a low-noise amplifier (LNA) with noise cancellation, an RF bandpass filter (BPF), a downconverter with linearization, and an intermediate frequency (IF) BPF. A noise canceling technique used in the low-noise amplifier eliminates a thermal noise and then reduces the noise figure (NF) of the RF front end by 0.9 dB. Use of a downconverter with diode linearizer also compensates for gain compression, which increases the input-referred third-order intercept point (IIP3) of the RF front end by 4.3 dB. The proposed method substantially increases the spurious-free dynamic range (DRf) of the RF front end by 3.5 dB

    Guidance and control research

    Get PDF
    Effective work function of metal contacts to vacuum cleaved photoconducting cadmium sulfide, Curie point switching experiments, and germanium diodes for noise measurement

    Instantaneous Capture and Mineralization of Flue Gas Carbon Dioxide: Pilot Scale Study

    Get PDF
    Multiple CO2 capture and storage (CCS) processes are required to address anthropogenic CO2 problems. However, a method which can directly capture and mineralize CO2 at a point source, under actual field conditions, has advantages and could help offset the cost associated with the conventional CCS technologies. The mineral carbonation (MC), a process of converting CO2 into stable minerals (mineralization), has been studied extensively to store CO2. However, most of the MC studies have been largely investigated at laboratory scale. Objectives of this research were to develop a pilot scale AMC (accelerated mineral carbonation) process and test the effects of flue gas moisture content on carbonation of fly ash particles. A pilot scale AMC process consisting of a moisture reducing drum (MRD), a heater/humidifier, and a fluidized-bed reactor (FBR) was developed and tested by reacting flue gas with fly ash particles at one of the largest coal-fired power plants (2120 MW) in the USA. The experiments were conducted over a period of 2 hr at ~ 300 SCFM flow-rates, at a controlled pressure (115.1 kPa), and under different flue gas moisture contents (2-16%). The flue gas CO2 and SO2 concentrations were monitored before and during the experiments by an industrial grade gas analyzer. Fly ash samples were collected from the reactor sample port from 0-120 minutes and analyzed for total inorganic carbon (C), sulfur (S), and mercury (Hg). From C, S, and Hg concentrations, %calcium carbonate (CaCO3), %sulfate (SO42-), and %mercury carbonate (HgCO3) were calculated, respectively. Results suggested significant mineralization of flue gas CO2, SO2, and Hg within 10-15 minutes of reaction. Among different moisture conditions, ~16% showed highest conversion of flue gas CO2 and SO2 to %CaCO3 and %SO42- in fly ash samples. For example, an increase of almost 4% in CaCO3 content of fly ash was observed. Overall, the AMC process is cost-effective with minimum carbon footprint and can be retrofitted to coal fired power plants (existing and/or new) as a post-combustion unit to minimize flue gas CO2, SO2, and Hg emissions into the atmosphere. Used in conjunction with capture and geologic sequestration, the AMC process has the potential to reduce overall cost associated with CO2 separation/compression/transportation/pore space/brine water treatment. It could also help protect sensitive amines and carbon filters used in flue gas CO2 capture and separation process and extend their life

    A 0.8 V T Network-Based 2.6 GHz Downconverter RFIC

    Get PDF
    A 2.6 GHz downconverter RFIC is designed and implemented using a 0.18 μm CMOS standard process. An important goal of the design is to achieve the high linearity that is required in WiMAX systems with a low supply voltage. A passive T phase-shift network is used as an RF input stage in a Gilbert cell to reduce supply voltage. A single supply voltage of 0.8 V is used with a power consumption of 5.87 mW. The T network-based downconverter achieves a conversion gain (CG) of 5 dB, a single-sideband noise figure (NF) of 16.16 dB, an RF-to-IF isolation of greater than 20 dB, and an input-referred third-order intercept point (IIP3) of 1 dBm when the LO power of -13 dBm is applied

    DAC-Less amplifier-less generation and transmission of QAM signals using sub-volt silicon-organic hybrid modulators

    Get PDF
    We demonstrate generation and transmission of optical signals by directly interfacing highly efficient silicon-organic hybrid (SOH) modulators to binary output ports of a field-programmable gate array. Using an SOH Mach-Zehnder modulator (MZM) and an SOH IQ modulator we generate ON-OFF- keying and binary phase-shift keying signals as well as quadrature phase-shift keying and 16-state quadrature amplitude modulation (16QAM) formats. Peak-to-peak voltages amount to only 0.27 V-pp for driving the MZM and 0.41 V-pp for the IQ modulator. Neither digital-to-analog converters nor drive amplifiers are required, and the RF energy consumption in the modulator amounts to record-low 18 fJ/bit for 16QAM signaling
    corecore